Vulcanworks

Applications:
2008-Up Sportsters with 25mm Bearings
2004-2005 Dyna With 1" Bearings
2008-2017 FLST & FXST
THIS AXLE IS ONLY FOR MODELS ABOVE WITH MID GLIDE CONVERSION TREES

This is a conversion axle that will allow you to use a wheel with 3/4" Bearings(Timken or Sealed) with the Front Ends Listed Above

Now Available for 7 Spoke 18" Morris Mags Wheels HD# 41037-77
We have made hubs that adapt this wheel to 2000-up applications.
Will drop in place of your 2000-Up  Rear Wheel with this kit.
Can also be used in place of timken bearing wheels with a 2000-Up Brake disc & Sprocket/Pulley

Now Available for 7 Spoke 19" Morris Mags Wheels
We have made hubs that adapt this wheel to replace 35mm and 39mm timken bearing applications.
Hubs have the correct width for 1984-1999 35mm and 39mm Front Ends.
We have eliminated the tapered wheel bearings, uses modern sealed ball bearings.
Must be used with 2000-Up Brake discs (2.2" Locating Diameter)
May Be used Dual or Single Disk

Includes:
Adapter Hubs
Inner Wheel Sleeve
Mounting Hardware
3/4" Bearings
Axle Spacers (To eliminate speedo drive)

(This does not include the wheel)

Now Available for 7 Spoke 19" Morris Mags Wheels
We have made hubs that adapt this wheel to replace 3/4", 1" and 25mm Wheels on 2000-Up 39mm Front Ends
Hubs have the correct width for 2000-Up 39mm Front Ends.
Uses stock 2000-Up Brake discs
May Be used Dual or Single Disk

Includes:
Adapter Hubs
Inner Wheel Sleeve
Mounting Hardware
3/4", 1" or 25mm Bearings

(This does not include the wheel)

Now Available for 7 Spoke 19" Morris Mags Wheels
We have made hubs that adapt this wheel to replace 1" and 25mm Wheels on 2006-Up 49mm Dyna Front Ends
Hubs have the correct width for 2006-Up Dyna Narrow/Mid Front Ends.(Not Wide Glide)
Uses stock 2006-Up Brake discs(Except large bolt pattern disks)
May Be used Dual or Single Disk

• 21 Tooth
• 1/4", 1/2", 3/4", 1", 1-1/4", and 1-1/2" Offsets Available
• 530 Chain Size

Fits 91-up 5 speed Harley Sportsters.
All of out offset transmission sprockets are based on the OEM XL sprocket #37709-89 used on 91-92 5 speed EVO's.
 

• 23 Tooth
• 1/4", 1/2", 3/4", .900", 1", 1-1/4", and 1-1/2" Offsets Available

For Harley 5 speed & 6 speed R/S & L/S Drive Transmissions.and 5 speed sportsters.
Will also fit stock left side drive transmissions.
Made from 4140 Machined Tool Steel

• 24 Tooth
• 1/4", 1/2", 3/4", .900", 1", 1-1/4", and 1-1/2" Offsets Available

For Harley 5 speed & 6 speed R/S & L/S Drive Transmissions.and 5 speed sportsters.
Will also fit stock left side drive transmissions.
Made in USA from Heat Treated Tool Steel

Set of 3 Plugs needed for one motor

Allows you to run an Oil Pressure Gauge when you replace the lifter screen plug with this adapter.

  Stainless Steel

1977-Up Harley XL Sportsters
Phosphorus Bronze

Replaces Harley # 26489-76

1977-Up Harley XL Sportsters
Phosphorus Bronze

Replaces Harley # 26431-76

3 Piece Plug Set

Use 2 on the oil pump and 1 on the engine case tappet screen port.

Made from Stainless Steel, no more rusty plugs sticking out on you motor.
 

Fits:
All EVOs
All Shovelheads
Panheads with Aluminum Oil Pumps